Add tests for the rust bindings, quite similar to the ones in cxx bindings.
This is how "cargo test" prints results:
Running tests/chip.rs (target/debug/deps/chip-b19008e6b9a10d2f)
running 6 tests test chip::create::nonexistent_file_failure ... ok test chip::create::no_dev_file_failure ... ok test chip::create::non_gpio_char_dev_file_failure ... ok test chip::create::existing ... ok test chip::configure::line_lookup ... ok test chip::configure::verify ... ok
test result: ok. 6 passed; 0 failed; 0 ignored; 0 measured; 0 filtered out; finished in 0.14s
Running tests/edge_event.rs (target/debug/deps/edge_event-5897a36c91efe0d4)
running 11 tests test edge_event::buffer_settings::default_capacity ... ok test edge_event::buffer_settings::user_defined_capacity ... ok test edge_event::buffer_settings::max_capacity ... ok test edge_event::failure::dir_out_edge_failure ... ok test edge_event::failure::wait_timeout ... ok test edge_event::verify::both_edges ... ok test edge_event::verify::multiple_events ... ok test edge_event::verify::edge_sequence ... ok test edge_event::verify::falling_edge ... ok test edge_event::verify::over_capacity ... ok test edge_event::verify::rising_edge ... ok
test result: ok. 11 passed; 0 failed; 0 ignored; 0 measured; 0 filtered out; finished in 0.98s
Running tests/info_event.rs (target/debug/deps/info_event-707c734e0820381c)
running 3 tests test info_event::watch::verify ... ok test info_event::watch::failure ... ok test info_event::watch::reconfigure ... ok
test result: ok. 3 passed; 0 failed; 0 ignored; 0 measured; 0 filtered out; finished in 0.26s
Running tests/line_config.rs (target/debug/deps/line_config-d376966750bf38a0)
running 9 tests test line_config::overrides::active_low ... ok test line_config::overrides::bias ... ok test line_config::default::verify ... ok test line_config::overrides::debounce_period ... ok test line_config::overrides::direction ... ok test line_config::overrides::drive ... ok test line_config::overrides::edge_detection ... ok test line_config::overrides::event_clock ... ok test line_config::overrides::output_value ... ok
test result: ok. 9 passed; 0 failed; 0 ignored; 0 measured; 0 filtered out; finished in 0.06s
Running tests/line_info.rs (target/debug/deps/line_info-5069196cfaa74ab7)
running 2 tests [40570.967204] gpio-1992 (hog): hogged as output/high [40570.974774] gpio-1956 (hog4): hogged as output/low [40570.975314] gpio-1955 (hog3): hogged as output/high test line_info::properties::verify ... ok test line_info::basic::verify ... ok
test result: ok. 2 passed; 0 failed; 0 ignored; 0 measured; 0 filtered out; finished in 0.31s
Running tests/line_request.rs (target/debug/deps/line_request-914b9fd8c84e2c4b)
running 7 tests test line_request::invalid_arguments::no_offsets ... ok test line_request::verify::read_values ... ok test line_request::verify::set_bias ... ok test line_request::verify::reconfigure_output_values ... ok test line_request::verify::empty_consumer ... ok test line_request::verify::set_output_values ... ok test line_request::verify::custom_consumer ... ok
test result: ok. 7 passed; 0 failed; 0 ignored; 0 measured; 0 filtered out; finished in 0.48s
Running tests/request_config.rs (target/debug/deps/request_config-99e366517cc0feda)
running 2 tests test request_config::verify::default ... ok test request_config::verify::initialized ... ok
test result: ok. 2 passed; 0 failed; 0 ignored; 0 measured; 0 filtered out; finished in 0.03s
Doc-tests libgpiod
running 0 tests
test result: ok. 0 passed; 0 failed; 0 ignored; 0 measured; 0 filtered out; finished in 0.00s
Signed-off-by: Viresh Kumar viresh.kumar@linaro.org --- bindings/rust/Cargo.toml | 3 + bindings/rust/src/line_request.rs | 1 + bindings/rust/tests/chip.rs | 96 +++++++ bindings/rust/tests/common/config.rs | 117 ++++++++ bindings/rust/tests/common/mod.rs | 16 ++ bindings/rust/tests/common/sim.rs | 306 ++++++++++++++++++++ bindings/rust/tests/edge_event.rs | 389 ++++++++++++++++++++++++++ bindings/rust/tests/info_event.rs | 126 +++++++++ bindings/rust/tests/line_config.rs | 187 +++++++++++++ bindings/rust/tests/line_info.rs | 90 ++++++ bindings/rust/tests/line_request.rs | 234 ++++++++++++++++ bindings/rust/tests/request_config.rs | 42 +++ 12 files changed, 1607 insertions(+) create mode 100644 bindings/rust/tests/chip.rs create mode 100644 bindings/rust/tests/common/config.rs create mode 100644 bindings/rust/tests/common/mod.rs create mode 100644 bindings/rust/tests/common/sim.rs create mode 100644 bindings/rust/tests/edge_event.rs create mode 100644 bindings/rust/tests/info_event.rs create mode 100644 bindings/rust/tests/line_config.rs create mode 100644 bindings/rust/tests/line_info.rs create mode 100644 bindings/rust/tests/line_request.rs create mode 100644 bindings/rust/tests/request_config.rs
diff --git a/bindings/rust/Cargo.toml b/bindings/rust/Cargo.toml index d5d81486fa2f..e2d6d5bb91b6 100644 --- a/bindings/rust/Cargo.toml +++ b/bindings/rust/Cargo.toml @@ -10,3 +10,6 @@ libc = ">=0.2.39" libgpiod-sys = { path = "libgpiod-sys" } thiserror = "1.0" vmm-sys-util = "=0.9.0" + +[dev-dependencies] +libgpiod-sys = { path = "libgpiod-sys", features = ["gpiosim"] } diff --git a/bindings/rust/src/line_request.rs b/bindings/rust/src/line_request.rs index bb338e72671d..c1dbbb397e73 100644 --- a/bindings/rust/src/line_request.rs +++ b/bindings/rust/src/line_request.rs @@ -15,6 +15,7 @@ use super::{bindings, ChipInternal, EdgeEventBuffer, Error, LineConfig, RequestC /// Line request operations /// /// Allows interaction with a set of requested lines. +#[derive(Debug)] pub struct LineRequest { request: *mut bindings::gpiod_line_request, } diff --git a/bindings/rust/tests/chip.rs b/bindings/rust/tests/chip.rs new file mode 100644 index 000000000000..4e64e9c7e291 --- /dev/null +++ b/bindings/rust/tests/chip.rs @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +mod common; + +mod chip { + use libc::{ENODEV, ENOENT, ENOTTY}; + + use vmm_sys_util::errno::Error as IoError; + + use crate::common::*; + use libgpiod::{Chip, Error as ChipError}; + + mod create { + use super::*; + + #[test] + fn nonexistent_file_failure() { + assert_eq!( + Chip::open("/dev/nonexistent").unwrap_err(), + ChipError::OperationFailed("Gpio Chip open", IoError::new(ENOENT)) + ); + } + + #[test] + fn no_dev_file_failure() { + assert_eq!( + Chip::open("/tmp").unwrap_err(), + ChipError::OperationFailed("Gpio Chip open", IoError::new(ENOTTY)) + ); + } + + #[test] + fn non_gpio_char_dev_file_failure() { + assert_eq!( + Chip::open("/dev/null").unwrap_err(), + ChipError::OperationFailed("Gpio Chip open", IoError::new(ENODEV)) + ); + } + + #[test] + fn existing() { + let sim = Sim::new(None, None, true).unwrap(); + Chip::open(sim.dev_path()).unwrap(); + } + } + + mod configure { + use super::*; + const NGPIO: u64 = 16; + const LABEL: &str = "foobar"; + + #[test] + fn verify() { + let sim = Sim::new(Some(NGPIO), Some(LABEL), true).unwrap(); + let chip = Chip::open(sim.dev_path()).unwrap(); + + assert_eq!(chip.get_label().unwrap(), LABEL); + assert_eq!(chip.get_name().unwrap(), sim.chip_name()); + assert_eq!(chip.get_path().unwrap(), sim.dev_path()); + assert_eq!(chip.get_num_lines(), NGPIO as u32); + chip.get_fd().unwrap(); + } + + #[test] + fn line_lookup() { + let sim = Sim::new(Some(NGPIO), None, false).unwrap(); + sim.set_line_name(0, "zero").unwrap(); + sim.set_line_name(2, "two").unwrap(); + sim.set_line_name(3, "three").unwrap(); + sim.set_line_name(5, "five").unwrap(); + sim.set_line_name(10, "ten").unwrap(); + sim.set_line_name(11, "ten").unwrap(); + sim.enable().unwrap(); + + let chip = Chip::open(sim.dev_path()).unwrap(); + + // Success case + assert_eq!(chip.find_line("zero").unwrap(), 0); + assert_eq!(chip.find_line("two").unwrap(), 2); + assert_eq!(chip.find_line("three").unwrap(), 3); + assert_eq!(chip.find_line("five").unwrap(), 5); + + // Success with duplicate names, should return first entry + assert_eq!(chip.find_line("ten").unwrap(), 10); + + // Failure + assert_eq!( + chip.find_line("nonexistent").unwrap_err(), + ChipError::OperationFailed("Gpio Chip find-line", IoError::new(ENOENT)) + ); + } + } +} diff --git a/bindings/rust/tests/common/config.rs b/bindings/rust/tests/common/config.rs new file mode 100644 index 000000000000..3abd9a8c4c8b --- /dev/null +++ b/bindings/rust/tests/common/config.rs @@ -0,0 +1,117 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +use std::sync::Arc; + +use crate::common::*; + +use libgpiod::{Bias, Chip, Direction, Edge, LineConfig, LineRequest, RequestConfig, Result}; + +//#[derive(Debug)] +pub(crate) struct TestConfig { + sim: Arc<Sim>, + chip: Option<Chip>, + request: Option<LineRequest>, + rconfig: RequestConfig, + lconfig: LineConfig, +} + +impl TestConfig { + pub(crate) fn new(ngpio: u64) -> Result<Self> { + Ok(Self { + sim: Arc::new(Sim::new(Some(ngpio), None, true)?), + chip: None, + request: None, + rconfig: RequestConfig::new().unwrap(), + lconfig: LineConfig::new().unwrap(), + }) + } + + pub(crate) fn set_pull(&self, offsets: &[u32], pulls: &[u32]) { + for i in 0..pulls.len() { + self.sim.set_pull(offsets[i], pulls[i] as i32).unwrap(); + } + } + + pub(crate) fn rconfig_consumer(&self, offsets: Option<&[u32]>, consumer: Option<&str>) { + if let Some(offsets) = offsets { + self.rconfig.set_offsets(offsets); + } + + if let Some(consumer) = consumer { + self.rconfig.set_consumer(consumer); + } + } + + pub(crate) fn rconfig(&self, offsets: Option<&[u32]>) { + self.rconfig_consumer(offsets, None); + } + + pub(crate) fn lconfig( + &mut self, + dir: Option<Direction>, + val: Option<u32>, + val_override: Option<(u32, u32)>, + edge: Option<Edge>, + bias: Option<Bias>, + ) { + if let Some(bias) = bias { + self.lconfig.set_bias_default(bias); + } + + if let Some(edge) = edge { + self.lconfig.set_edge_detection_default(edge); + } + + if let Some(dir) = dir { + self.lconfig.set_direction_default(dir); + } + + if let Some(val) = val { + self.lconfig.set_output_value_default(val); + } + + if let Some((offset, val)) = val_override { + self.lconfig.set_output_value_override(val, offset); + } + } + + pub(crate) fn lconfig_raw(&mut self) { + self.lconfig(None, None, None, None, None); + } + + pub(crate) fn lconfig_edge(&mut self, edge: Option<Edge>) { + self.lconfig(None, None, None, edge, None); + } + + pub(crate) fn request_lines(&mut self) -> Result<()> { + let chip = Chip::open(self.sim.dev_path())?; + + self.request = Some(chip.request_lines(&self.rconfig, &self.lconfig)?); + self.chip = Some(chip); + + Ok(()) + } + + pub(crate) fn sim(&self) -> Arc<Sim> { + self.sim.clone() + } + + pub(crate) fn chip(&self) -> &Chip { + &self.chip.as_ref().unwrap() + } + + pub(crate) fn request(&self) -> &LineRequest { + &self.request.as_ref().unwrap() + } +} + +impl Drop for TestConfig { + fn drop(&mut self) { + // Explicit freeing is important to make sure "request" get freed + // before "sim" and "chip". + self.request = None; + } +} diff --git a/bindings/rust/tests/common/mod.rs b/bindings/rust/tests/common/mod.rs new file mode 100644 index 000000000000..2dc37986396b --- /dev/null +++ b/bindings/rust/tests/common/mod.rs @@ -0,0 +1,16 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +#[allow(dead_code)] +mod sim; + +#[allow(unused_imports)] +pub(crate) use sim::*; + +#[allow(dead_code)] +mod config; + +#[allow(unused_imports)] +pub(crate) use config::*; diff --git a/bindings/rust/tests/common/sim.rs b/bindings/rust/tests/common/sim.rs new file mode 100644 index 000000000000..cd5ec66c3da5 --- /dev/null +++ b/bindings/rust/tests/common/sim.rs @@ -0,0 +1,306 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +use std::os::raw::c_char; +use std::{slice, str}; + +use vmm_sys_util::errno::Error as IoError; + +use libgpiod::{Error, Result}; +use libgpiod_sys as bindings; + +/// Sim Ctx +#[derive(Debug)] +struct SimCtx { + ctx: *mut bindings::gpiosim_ctx, +} + +unsafe impl Send for SimCtx {} +unsafe impl Sync for SimCtx {} + +impl SimCtx { + fn new() -> Result<Self> { + let ctx = unsafe { bindings::gpiosim_ctx_new() }; + if ctx.is_null() { + return Err(Error::OperationFailed("gpio-sim ctx new", IoError::last())); + } + + Ok(Self { ctx }) + } + + fn ctx(&self) -> *mut bindings::gpiosim_ctx { + self.ctx + } +} + +impl Drop for SimCtx { + fn drop(&mut self) { + unsafe { bindings::gpiosim_ctx_unref(self.ctx) } + } +} + +/// Sim Dev +#[derive(Debug)] +struct SimDev { + dev: *mut bindings::gpiosim_dev, +} + +unsafe impl Send for SimDev {} +unsafe impl Sync for SimDev {} + +impl SimDev { + fn new(ctx: &SimCtx) -> Result<Self> { + let dev = unsafe { bindings::gpiosim_dev_new(ctx.ctx()) }; + if dev.is_null() { + return Err(Error::OperationFailed("gpio-sim dev new", IoError::last())); + } + + Ok(Self { dev }) + } + + fn dev(&self) -> *mut bindings::gpiosim_dev { + self.dev + } + + fn enable(&self) -> Result<()> { + let ret = unsafe { bindings::gpiosim_dev_enable(self.dev) }; + + if ret == -1 { + Err(Error::OperationFailed( + "gpio-sim dev-enable", + IoError::last(), + )) + } else { + Ok(()) + } + } + + fn disable(&self) -> Result<()> { + let ret = unsafe { bindings::gpiosim_dev_disable(self.dev) }; + + if ret == -1 { + Err(Error::OperationFailed( + "gpio-sim dev-disable", + IoError::last(), + )) + } else { + Ok(()) + } + } +} + +impl Drop for SimDev { + fn drop(&mut self) { + unsafe { bindings::gpiosim_dev_unref(self.dev) } + } +} + +/// Sim Bank +#[derive(Debug)] +struct SimBank { + bank: *mut bindings::gpiosim_bank, +} + +unsafe impl Send for SimBank {} +unsafe impl Sync for SimBank {} + +impl SimBank { + fn new(dev: &SimDev) -> Result<Self> { + let bank = unsafe { bindings::gpiosim_bank_new(dev.dev()) }; + if bank.is_null() { + return Err(Error::OperationFailed("gpio-sim Bank new", IoError::last())); + } + + Ok(Self { bank }) + } + + fn chip_name(&self) -> Result<&str> { + // SAFETY: The string returned by gpiosim is guaranteed to live as long + // as the `struct SimBank`. + let name = unsafe { bindings::gpiosim_bank_get_chip_name(self.bank) }; + + // SAFETY: The string is guaranteed to be valid here. + str::from_utf8(unsafe { + slice::from_raw_parts(name as *const u8, bindings::strlen(name) as usize) + }) + .map_err(Error::InvalidString) + } + + fn dev_path(&self) -> Result<&str> { + // SAFETY: The string returned by gpiosim is guaranteed to live as long + // as the `struct SimBank`. + let path = unsafe { bindings::gpiosim_bank_get_dev_path(self.bank) }; + + // SAFETY: The string is guaranteed to be valid here. + str::from_utf8(unsafe { + slice::from_raw_parts(path as *const u8, bindings::strlen(path) as usize) + }) + .map_err(Error::InvalidString) + } + + fn val(&self, offset: u32) -> Result<u32> { + let ret = unsafe { bindings::gpiosim_bank_get_value(self.bank, offset) }; + + if ret == -1 { + Err(Error::OperationFailed( + "gpio-sim get-value", + IoError::last(), + )) + } else { + Ok(ret as u32) + } + } + + fn set_label(&self, label: &str) -> Result<()> { + // Null-terminate the string + let label = label.to_owned() + "\0"; + + let ret = + unsafe { bindings::gpiosim_bank_set_label(self.bank, label.as_ptr() as *const c_char) }; + + if ret == -1 { + Err(Error::OperationFailed( + "gpio-sim set-label", + IoError::last(), + )) + } else { + Ok(()) + } + } + + fn set_num_lines(&self, num: u64) -> Result<()> { + let ret = unsafe { bindings::gpiosim_bank_set_num_lines(self.bank, num) }; + if ret == -1 { + Err(Error::OperationFailed( + "gpio-sim set-num-lines", + IoError::last(), + )) + } else { + Ok(()) + } + } + + fn set_line_name(&self, offset: u32, name: &str) -> Result<()> { + // Null-terminate the string + let name = name.to_owned() + "\0"; + + let ret = unsafe { + bindings::gpiosim_bank_set_line_name(self.bank, offset, name.as_ptr() as *const c_char) + }; + + if ret == -1 { + Err(Error::OperationFailed( + "gpio-sim set-line-name", + IoError::last(), + )) + } else { + Ok(()) + } + } + + fn set_pull(&self, offset: u32, pull: i32) -> Result<()> { + let ret = unsafe { bindings::gpiosim_bank_set_pull(self.bank, offset, pull) }; + + if ret == -1 { + Err(Error::OperationFailed("gpio-sim set-pull", IoError::last())) + } else { + Ok(()) + } + } + + fn hog_line(&self, offset: u32, name: &str, dir: i32) -> Result<()> { + // Null-terminate the string + let name = name.to_owned() + "\0"; + + let ret = unsafe { + bindings::gpiosim_bank_hog_line(self.bank, offset, name.as_ptr() as *const c_char, dir) + }; + + if ret == -1 { + Err(Error::OperationFailed("gpio-sim hog-line", IoError::last())) + } else { + Ok(()) + } + } +} + +impl Drop for SimBank { + fn drop(&mut self) { + unsafe { bindings::gpiosim_bank_unref(self.bank) } + } +} + +/// GPIO SIM +#[derive(Debug)] +pub(crate) struct Sim { + ctx: SimCtx, + dev: SimDev, + bank: SimBank, +} + +unsafe impl Send for Sim {} +unsafe impl Sync for Sim {} + +impl Sim { + pub(crate) fn new(ngpio: Option<u64>, label: Option<&str>, enable: bool) -> Result<Self> { + let ctx = SimCtx::new()?; + let dev = SimDev::new(&ctx)?; + let bank = SimBank::new(&dev)?; + + if let Some(ngpio) = ngpio { + bank.set_num_lines(ngpio)?; + } + + if let Some(label) = label { + bank.set_label(label)?; + } + + if enable { + dev.enable()?; + } + + Ok(Self { ctx, dev, bank }) + } + + pub(crate) fn chip_name(&self) -> &str { + self.bank.chip_name().unwrap() + } + + pub fn dev_path(&self) -> &str { + self.bank.dev_path().unwrap() + } + + pub(crate) fn val(&self, offset: u32) -> Result<u32> { + self.bank.val(offset) + } + + pub(crate) fn set_label(&self, label: &str) -> Result<()> { + self.bank.set_label(label) + } + + pub(crate) fn set_num_lines(&self, num: u64) -> Result<()> { + self.bank.set_num_lines(num) + } + + pub(crate) fn set_line_name(&self, offset: u32, name: &str) -> Result<()> { + self.bank.set_line_name(offset, name) + } + + pub(crate) fn set_pull(&self, offset: u32, pull: i32) -> Result<()> { + self.bank.set_pull(offset, pull) + } + + pub(crate) fn hog_line(&self, offset: u32, name: &str, dir: i32) -> Result<()> { + self.bank.hog_line(offset, name, dir) + } + + pub(crate) fn enable(&self) -> Result<()> { + self.dev.enable() + } + + pub(crate) fn disable(&self) -> Result<()> { + self.dev.disable() + } +} diff --git a/bindings/rust/tests/edge_event.rs b/bindings/rust/tests/edge_event.rs new file mode 100644 index 000000000000..1b05b225aab7 --- /dev/null +++ b/bindings/rust/tests/edge_event.rs @@ -0,0 +1,389 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +mod common; + +mod edge_event { + use libc::EINVAL; + use std::sync::Arc; + use std::thread::{sleep, spawn}; + use std::time::Duration; + + use vmm_sys_util::errno::Error as IoError; + + use crate::common::*; + use libgpiod::{Direction, Edge, EdgeEventBuffer, Error as ChipError, LineEdgeEvent}; + use libgpiod_sys::{GPIOSIM_PULL_DOWN, GPIOSIM_PULL_UP}; + + const NGPIO: u64 = 8; + + mod buffer_settings { + use super::*; + + #[test] + fn default_capacity() { + assert_eq!(EdgeEventBuffer::new(0).unwrap().get_capacity(), 64); + } + + #[test] + fn user_defined_capacity() { + assert_eq!(EdgeEventBuffer::new(123).unwrap().get_capacity(), 123); + } + + #[test] + fn max_capacity() { + assert_eq!(EdgeEventBuffer::new(1024 * 2).unwrap().get_capacity(), 1024); + } + } + + mod failure { + use super::*; + + #[test] + fn wait_timeout() { + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[0])); + config.lconfig_edge(Some(Edge::Both)); + config.request_lines().unwrap(); + + // No events available + assert_eq!( + config + .request() + .wait_edge_event(Duration::from_millis(100)) + .unwrap_err(), + ChipError::OperationTimedOut + ); + } + + #[test] + fn dir_out_edge_failure() { + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[0])); + config.lconfig(Some(Direction::Output), None, None, Some(Edge::Both), None); + + assert_eq!( + config.request_lines().unwrap_err(), + ChipError::OperationFailed("Gpio LineRequest request-lines", IoError::new(EINVAL)) + ); + } + } + + mod verify { + use super::*; + + // Helpers to generate events + fn trigger_falling_and_rising_edge(sim: Arc<Sim>, offset: u32) { + spawn(move || { + sleep(Duration::from_millis(30)); + sim.set_pull(offset, GPIOSIM_PULL_UP as i32).unwrap(); + + sleep(Duration::from_millis(30)); + sim.set_pull(offset, GPIOSIM_PULL_DOWN as i32).unwrap(); + }); + } + + fn trigger_rising_edge_events_on_two_offsets(sim: Arc<Sim>, offset: [u32; 2]) { + spawn(move || { + sleep(Duration::from_millis(30)); + sim.set_pull(offset[0], GPIOSIM_PULL_UP as i32).unwrap(); + + sleep(Duration::from_millis(30)); + sim.set_pull(offset[1], GPIOSIM_PULL_UP as i32).unwrap(); + }); + } + + fn trigger_multiple_events(sim: Arc<Sim>, offset: u32) { + sim.set_pull(offset, GPIOSIM_PULL_UP as i32).unwrap(); + sleep(Duration::from_millis(10)); + + sim.set_pull(offset, GPIOSIM_PULL_DOWN as i32).unwrap(); + sleep(Duration::from_millis(10)); + + sim.set_pull(offset, GPIOSIM_PULL_UP as i32).unwrap(); + sleep(Duration::from_millis(10)); + } + + #[test] + fn both_edges() { + const GPIO: u32 = 2; + let buf = EdgeEventBuffer::new(0).unwrap(); + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[GPIO])); + config.lconfig_edge(Some(Edge::Both)); + config.request_lines().unwrap(); + + // Generate events + trigger_falling_and_rising_edge(config.sim(), GPIO); + + // Rising event + config + .request() + .wait_edge_event(Duration::from_secs(1)) + .unwrap(); + + assert_eq!( + config + .request() + .read_edge_event(&buf, buf.get_capacity()) + .unwrap(), + 1 + ); + assert_eq!(buf.get_num_events(), 1); + + let event = buf.get_event(0).unwrap(); + let ts_rising = event.get_timestamp(); + assert_eq!(event.get_event_type().unwrap(), LineEdgeEvent::Rising); + assert_eq!(event.get_line_offset(), GPIO); + + // Falling event + config + .request() + .wait_edge_event(Duration::from_secs(1)) + .unwrap(); + + assert_eq!( + config + .request() + .read_edge_event(&buf, buf.get_capacity()) + .unwrap(), + 1 + ); + assert_eq!(buf.get_num_events(), 1); + + let event = buf.get_event(0).unwrap(); + let ts_falling = event.get_timestamp(); + assert_eq!(event.get_event_type().unwrap(), LineEdgeEvent::Falling); + assert_eq!(event.get_line_offset(), GPIO); + + // No events available + assert_eq!( + config + .request() + .wait_edge_event(Duration::from_millis(100)) + .unwrap_err(), + ChipError::OperationTimedOut + ); + + assert!(ts_falling > ts_rising); + } + + #[test] + fn rising_edge() { + const GPIO: u32 = 6; + let buf = EdgeEventBuffer::new(0).unwrap(); + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[GPIO])); + config.lconfig_edge(Some(Edge::Rising)); + config.request_lines().unwrap(); + + // Generate events + trigger_falling_and_rising_edge(config.sim(), GPIO); + + // Rising event + config + .request() + .wait_edge_event(Duration::from_secs(1)) + .unwrap(); + + assert_eq!( + config + .request() + .read_edge_event(&buf, buf.get_capacity()) + .unwrap(), + 1 + ); + assert_eq!(buf.get_num_events(), 1); + + let event = buf.get_event(0).unwrap(); + assert_eq!(event.get_event_type().unwrap(), LineEdgeEvent::Rising); + assert_eq!(event.get_line_offset(), GPIO); + + // No events available + assert_eq!( + config + .request() + .wait_edge_event(Duration::from_millis(100)) + .unwrap_err(), + ChipError::OperationTimedOut + ); + } + + #[test] + fn falling_edge() { + const GPIO: u32 = 7; + let buf = EdgeEventBuffer::new(0).unwrap(); + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[GPIO])); + config.lconfig_edge(Some(Edge::Falling)); + config.request_lines().unwrap(); + + // Generate events + trigger_falling_and_rising_edge(config.sim(), GPIO); + + // Falling event + config + .request() + .wait_edge_event(Duration::from_secs(1)) + .unwrap(); + + assert_eq!( + config + .request() + .read_edge_event(&buf, buf.get_capacity()) + .unwrap(), + 1 + ); + assert_eq!(buf.get_num_events(), 1); + + let event = buf.get_event(0).unwrap(); + assert_eq!(event.get_event_type().unwrap(), LineEdgeEvent::Falling); + assert_eq!(event.get_line_offset(), GPIO); + + // No events available + assert_eq!( + config + .request() + .wait_edge_event(Duration::from_millis(100)) + .unwrap_err(), + ChipError::OperationTimedOut + ); + } + + #[test] + fn edge_sequence() { + const GPIO: [u32; 2] = [0, 1]; + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&GPIO)); + config.lconfig_edge(Some(Edge::Both)); + config.request_lines().unwrap(); + + // Generate events + trigger_rising_edge_events_on_two_offsets(config.sim(), GPIO); + + // Rising event GPIO 0 + let buf = EdgeEventBuffer::new(0).unwrap(); + config + .request() + .wait_edge_event(Duration::from_secs(1)) + .unwrap(); + + assert_eq!( + config + .request() + .read_edge_event(&buf, buf.get_capacity()) + .unwrap(), + 1 + ); + assert_eq!(buf.get_num_events(), 1); + + let event = buf.get_event(0).unwrap(); + assert_eq!(event.get_event_type().unwrap(), LineEdgeEvent::Rising); + assert_eq!(event.get_line_offset(), GPIO[0]); + assert_eq!(event.get_global_seqno(), 1); + assert_eq!(event.get_line_seqno(), 1); + + // Rising event GPIO 1 + config + .request() + .wait_edge_event(Duration::from_secs(1)) + .unwrap(); + + assert_eq!( + config + .request() + .read_edge_event(&buf, buf.get_capacity()) + .unwrap(), + 1 + ); + assert_eq!(buf.get_num_events(), 1); + + let event = buf.get_event(0).unwrap(); + assert_eq!(event.get_event_type().unwrap(), LineEdgeEvent::Rising); + assert_eq!(event.get_line_offset(), GPIO[1]); + assert_eq!(event.get_global_seqno(), 2); + assert_eq!(event.get_line_seqno(), 1); + + // No events available + assert_eq!( + config + .request() + .wait_edge_event(Duration::from_millis(100)) + .unwrap_err(), + ChipError::OperationTimedOut + ); + } + + #[test] + fn multiple_events() { + const GPIO: u32 = 1; + let buf = EdgeEventBuffer::new(0).unwrap(); + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[GPIO])); + config.lconfig_edge(Some(Edge::Both)); + config.request_lines().unwrap(); + + // Generate events + trigger_multiple_events(config.sim(), GPIO); + + // Read multiple events + config + .request() + .wait_edge_event(Duration::from_secs(1)) + .unwrap(); + + assert_eq!( + config + .request() + .read_edge_event(&buf, buf.get_capacity()) + .unwrap(), + 3 + ); + assert_eq!(buf.get_num_events(), 3); + + let mut global_seqno = 1; + let mut line_seqno = 1; + + // Verify sequence number of events + for i in 0..3 { + let event = buf.get_event(i).unwrap(); + assert_eq!(event.get_line_offset(), GPIO); + assert_eq!(event.get_global_seqno(), global_seqno); + assert_eq!(event.get_line_seqno(), line_seqno); + + global_seqno += 1; + line_seqno += 1; + } + } + + #[test] + fn over_capacity() { + const GPIO: u32 = 2; + let buf = EdgeEventBuffer::new(2).unwrap(); + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[GPIO])); + config.lconfig_edge(Some(Edge::Both)); + config.request_lines().unwrap(); + + // Generate events + trigger_multiple_events(config.sim(), GPIO); + + // Read multiple events + config + .request() + .wait_edge_event(Duration::from_secs(1)) + .unwrap(); + + assert_eq!( + config + .request() + .read_edge_event(&buf, buf.get_capacity()) + .unwrap(), + 2 + ); + assert_eq!(buf.get_num_events(), 2); + } + } +} diff --git a/bindings/rust/tests/info_event.rs b/bindings/rust/tests/info_event.rs new file mode 100644 index 000000000000..96d8385deadf --- /dev/null +++ b/bindings/rust/tests/info_event.rs @@ -0,0 +1,126 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +mod common; + +mod info_event { + use libc::EINVAL; + use std::sync::Arc; + use std::thread::{sleep, spawn}; + use std::time::Duration; + + use vmm_sys_util::errno::Error as IoError; + + use crate::common::*; + use libgpiod::{Chip, Direction, Error as ChipError, Event, LineConfig, RequestConfig}; + + fn request_reconfigure_line(chip: Arc<Chip>) { + spawn(move || { + sleep(Duration::from_millis(10)); + + let lconfig1 = LineConfig::new().unwrap(); + let rconfig = RequestConfig::new().unwrap(); + rconfig.set_offsets(&[7]); + + let request = chip.request_lines(&rconfig, &lconfig1).unwrap(); + + sleep(Duration::from_millis(10)); + + let mut lconfig2 = LineConfig::new().unwrap(); + lconfig2.set_direction_default(Direction::Output); + + request.reconfigure_lines(&lconfig2).unwrap(); + + sleep(Duration::from_millis(10)); + }); + } + + mod watch { + use super::*; + const NGPIO: u64 = 8; + const GPIO: u32 = 7; + + #[test] + fn failure() { + let sim = Sim::new(Some(NGPIO), None, true).unwrap(); + let chip = Chip::open(sim.dev_path()).unwrap(); + + assert_eq!( + chip.watch_line_info(NGPIO as u32).unwrap_err(), + ChipError::OperationFailed("Gpio LineInfo line-info", IoError::new(EINVAL)) + ); + + chip.watch_line_info(3).unwrap(); + + // No events available + assert_eq!( + chip.wait_info_event(Duration::from_millis(100)) + .unwrap_err(), + ChipError::OperationTimedOut + ); + } + + #[test] + fn verify() { + let sim = Sim::new(Some(NGPIO), None, true).unwrap(); + let chip = Chip::open(sim.dev_path()).unwrap(); + let info = chip.watch_line_info(GPIO).unwrap(); + + assert_eq!(info.get_offset(), GPIO); + } + + #[test] + fn reconfigure() { + let sim = Sim::new(Some(NGPIO), None, true).unwrap(); + let chip = Arc::new(Chip::open(sim.dev_path()).unwrap()); + let info = chip.watch_line_info(GPIO).unwrap(); + + assert_eq!(info.get_direction().unwrap(), Direction::Input); + + // Generate events + request_reconfigure_line(chip.clone()); + + // Line requested event + chip.wait_info_event(Duration::from_secs(1)).unwrap(); + let event = chip.read_info_event().unwrap(); + let ts_req = event.get_timestamp(); + + assert_eq!(event.get_event_type().unwrap(), Event::LineRequested); + assert_eq!( + event.line_info().unwrap().get_direction().unwrap(), + Direction::Input + ); + + // Line changed event + chip.wait_info_event(Duration::from_secs(1)).unwrap(); + let event = chip.read_info_event().unwrap(); + let ts_rec = event.get_timestamp(); + + assert_eq!(event.get_event_type().unwrap(), Event::LineConfigChanged); + assert_eq!( + event.line_info().unwrap().get_direction().unwrap(), + Direction::Output + ); + + // Line released event + chip.wait_info_event(Duration::from_secs(1)).unwrap(); + let event = chip.read_info_event().unwrap(); + let ts_rel = event.get_timestamp(); + + assert_eq!(event.get_event_type().unwrap(), Event::LineReleased); + + // No events available + assert_eq!( + chip.wait_info_event(Duration::from_millis(100)) + .unwrap_err(), + ChipError::OperationTimedOut + ); + + // Check timestamps are really monotonic. + assert!(ts_rel > ts_rec); + assert!(ts_rec > ts_req); + } + } +} diff --git a/bindings/rust/tests/line_config.rs b/bindings/rust/tests/line_config.rs new file mode 100644 index 000000000000..82879324a7f0 --- /dev/null +++ b/bindings/rust/tests/line_config.rs @@ -0,0 +1,187 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +mod common; + +mod line_config { + use std::time::Duration; + + use libgpiod::{Bias, Direction, Drive, Edge, EventClock, LineConfig}; + + mod default { + use super::*; + + #[test] + fn verify() { + let lconfig = LineConfig::new().unwrap(); + + assert_eq!(lconfig.get_direction_default().unwrap(), Direction::AsIs); + assert_eq!(lconfig.get_edge_detection_default().unwrap(), Edge::None); + assert_eq!(lconfig.get_bias_default().unwrap(), Bias::AsIs); + assert_eq!(lconfig.get_drive_default().unwrap(), Drive::PushPull); + assert_eq!(lconfig.get_active_low_default(), false); + assert_eq!( + lconfig.get_debounce_period_default().unwrap(), + Duration::from_millis(0) + ); + assert_eq!( + lconfig.get_event_clock_default().unwrap(), + EventClock::Monotonic + ); + assert_eq!(lconfig.get_output_value_default().unwrap(), 0); + assert_eq!(lconfig.get_overrides().unwrap().len(), 0); + } + } + + mod overrides { + use super::*; + + #[test] + fn direction() { + const GPIO: u32 = 0; + let mut lconfig = LineConfig::new().unwrap(); + + lconfig.set_direction_default(Direction::AsIs); + lconfig.set_direction_override(Direction::Input, GPIO); + + assert_eq!(lconfig.direction_is_overridden(GPIO), true); + assert_eq!( + lconfig.get_direction_offset(GPIO).unwrap(), + Direction::Input + ); + + lconfig.clear_direction_override(GPIO); + assert_eq!(lconfig.direction_is_overridden(GPIO), false); + assert_eq!(lconfig.get_direction_offset(GPIO).unwrap(), Direction::AsIs); + } + + #[test] + fn edge_detection() { + const GPIO: u32 = 1; + let mut lconfig = LineConfig::new().unwrap(); + + lconfig.set_edge_detection_default(Edge::None); + lconfig.set_edge_detection_override(Edge::Both, GPIO); + + assert_eq!(lconfig.edge_detection_is_overridden(GPIO), true); + assert_eq!(lconfig.get_edge_detection_offset(GPIO).unwrap(), Edge::Both); + + lconfig.clear_edge_detection_override(GPIO); + assert_eq!(lconfig.edge_detection_is_overridden(GPIO), false); + assert_eq!(lconfig.get_edge_detection_offset(GPIO).unwrap(), Edge::None); + } + + #[test] + fn bias() { + const GPIO: u32 = 2; + let mut lconfig = LineConfig::new().unwrap(); + + lconfig.set_bias_default(Bias::AsIs); + lconfig.set_bias_override(Bias::PullDown, GPIO); + + assert_eq!(lconfig.bias_is_overridden(GPIO), true); + assert_eq!(lconfig.get_bias_offset(GPIO).unwrap(), Bias::PullDown); + + lconfig.clear_bias_override(GPIO); + assert_eq!(lconfig.bias_is_overridden(GPIO), false); + assert_eq!(lconfig.get_bias_offset(GPIO).unwrap(), Bias::AsIs); + } + + #[test] + fn drive() { + const GPIO: u32 = 3; + let mut lconfig = LineConfig::new().unwrap(); + + lconfig.set_drive_default(Drive::PushPull); + lconfig.set_drive_override(Drive::OpenDrain, GPIO); + + assert_eq!(lconfig.drive_is_overridden(GPIO), true); + assert_eq!(lconfig.get_drive_offset(GPIO).unwrap(), Drive::OpenDrain); + + lconfig.clear_drive_override(GPIO); + assert_eq!(lconfig.drive_is_overridden(GPIO), false); + assert_eq!(lconfig.get_drive_offset(GPIO).unwrap(), Drive::PushPull); + } + + #[test] + fn active_low() { + const GPIO: u32 = 4; + let mut lconfig = LineConfig::new().unwrap(); + + lconfig.set_active_low_default(false); + lconfig.set_active_low_override(true, GPIO); + + assert_eq!(lconfig.active_low_is_overridden(GPIO), true); + assert_eq!(lconfig.get_active_low_offset(GPIO), true); + + lconfig.clear_active_low_override(GPIO); + assert_eq!(lconfig.active_low_is_overridden(GPIO), false); + assert_eq!(lconfig.get_active_low_offset(GPIO), false); + } + + #[test] + fn debounce_period() { + const GPIO: u32 = 5; + let mut lconfig = LineConfig::new().unwrap(); + + lconfig.set_debounce_period_default(Duration::from_millis(5)); + lconfig.set_debounce_period_override(Duration::from_millis(3), GPIO); + + assert_eq!(lconfig.debounce_period_is_overridden(GPIO), true); + assert_eq!( + lconfig.get_debounce_period_offset(GPIO).unwrap(), + Duration::from_millis(3) + ); + + lconfig.clear_debounce_period_override(GPIO); + assert_eq!(lconfig.debounce_period_is_overridden(GPIO), false); + assert_eq!( + lconfig.get_debounce_period_offset(GPIO).unwrap(), + Duration::from_millis(5) + ); + } + + #[test] + fn event_clock() { + const GPIO: u32 = 6; + let mut lconfig = LineConfig::new().unwrap(); + + lconfig.set_event_clock_default(EventClock::Monotonic); + lconfig.set_event_clock_override(EventClock::Realtime, GPIO); + + assert_eq!(lconfig.event_clock_is_overridden(GPIO), true); + assert_eq!( + lconfig.get_event_clock_offset(GPIO).unwrap(), + EventClock::Realtime + ); + + lconfig.clear_event_clock_override(GPIO); + assert_eq!(lconfig.event_clock_is_overridden(GPIO), false); + assert_eq!( + lconfig.get_event_clock_offset(GPIO).unwrap(), + EventClock::Monotonic + ); + } + + #[test] + fn output_value() { + const GPIO: u32 = 0; + let mut lconfig = LineConfig::new().unwrap(); + + lconfig.set_output_value_default(0); + lconfig.set_output_value_override(1, GPIO); + lconfig.set_output_values(&[1, 2, 8], &[1, 1, 1]).unwrap(); + + for line in [0, 1, 2, 8] { + assert_eq!(lconfig.output_value_is_overridden(line), true); + assert_eq!(lconfig.get_output_value_offset(line).unwrap(), 1); + + lconfig.clear_output_value_override(line); + assert_eq!(lconfig.output_value_is_overridden(line), false); + assert_eq!(lconfig.get_output_value_offset(line).unwrap(), 0); + } + } + } +} diff --git a/bindings/rust/tests/line_info.rs b/bindings/rust/tests/line_info.rs new file mode 100644 index 000000000000..f6f8f592cc85 --- /dev/null +++ b/bindings/rust/tests/line_info.rs @@ -0,0 +1,90 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +mod common; + +mod line_info { + use libc::EINVAL; + use std::time::Duration; + + use vmm_sys_util::errno::Error as IoError; + + use crate::common::*; + use libgpiod::{Bias, Chip, Direction, Drive, Edge, Error as ChipError, EventClock}; + use libgpiod_sys::{GPIOSIM_HOG_DIR_OUTPUT_HIGH, GPIOSIM_HOG_DIR_OUTPUT_LOW}; + + const NGPIO: u64 = 8; + + mod basic { + use super::*; + + #[test] + fn verify() { + const GPIO: u32 = 0; + const LABEL: &str = "foobar"; + let sim = Sim::new(Some(NGPIO), None, false).unwrap(); + sim.set_line_name(GPIO, LABEL).unwrap(); + sim.hog_line(GPIO, "hog", GPIOSIM_HOG_DIR_OUTPUT_HIGH as i32) + .unwrap(); + sim.enable().unwrap(); + + let chip = Chip::open(sim.dev_path()).unwrap(); + let info = chip.line_info(GPIO).unwrap(); + + assert_eq!(info.get_offset(), GPIO); + assert_eq!(info.get_name().unwrap(), LABEL); + assert_eq!(info.is_used(), true); + assert_eq!(info.get_consumer().unwrap(), "hog"); + assert_eq!(info.get_direction().unwrap(), Direction::Output); + assert_eq!(info.is_active_low(), false); + assert_eq!(info.get_bias().unwrap(), Bias::Unknown); + assert_eq!(info.get_drive().unwrap(), Drive::PushPull); + assert_eq!(info.get_edge_detection().unwrap(), Edge::None); + assert_eq!(info.get_event_clock().unwrap(), EventClock::Monotonic); + assert_eq!(info.is_debounced(), false); + assert_eq!(info.get_debounce_period(), Duration::from_millis(0)); + + assert_eq!( + chip.line_info(NGPIO as u32).unwrap_err(), + ChipError::OperationFailed("Gpio LineInfo line-info", IoError::new(EINVAL)) + ); + } + } + + mod properties { + use super::*; + + #[test] + fn verify() { + let sim = Sim::new(Some(NGPIO), None, false).unwrap(); + sim.set_line_name(1, "one").unwrap(); + sim.set_line_name(2, "two").unwrap(); + sim.set_line_name(4, "four").unwrap(); + sim.set_line_name(5, "five").unwrap(); + sim.hog_line(3, "hog3", GPIOSIM_HOG_DIR_OUTPUT_HIGH as i32) + .unwrap(); + sim.hog_line(4, "hog4", GPIOSIM_HOG_DIR_OUTPUT_LOW as i32) + .unwrap(); + sim.enable().unwrap(); + + let chip = Chip::open(sim.dev_path()).unwrap(); + chip.line_info(6).unwrap(); + + let info4 = chip.line_info(4).unwrap(); + assert_eq!(info4.get_offset(), 4); + assert_eq!(info4.get_name().unwrap(), "four"); + assert_eq!(info4.is_used(), true); + assert_eq!(info4.get_consumer().unwrap(), "hog4"); + assert_eq!(info4.get_direction().unwrap(), Direction::Output); + assert_eq!(info4.is_active_low(), false); + assert_eq!(info4.get_bias().unwrap(), Bias::Unknown); + assert_eq!(info4.get_drive().unwrap(), Drive::PushPull); + assert_eq!(info4.get_edge_detection().unwrap(), Edge::None); + assert_eq!(info4.get_event_clock().unwrap(), EventClock::Monotonic); + assert_eq!(info4.is_debounced(), false); + assert_eq!(info4.get_debounce_period(), Duration::from_millis(0)); + } + } +} diff --git a/bindings/rust/tests/line_request.rs b/bindings/rust/tests/line_request.rs new file mode 100644 index 000000000000..361ee6318d2e --- /dev/null +++ b/bindings/rust/tests/line_request.rs @@ -0,0 +1,234 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +mod common; + +mod line_request { + use libc::{EBUSY, EINVAL}; + + use vmm_sys_util::errno::Error as IoError; + + use crate::common::*; + use libgpiod::{Bias, Direction, Error as ChipError, LineConfig}; + use libgpiod_sys::{ + GPIOSIM_PULL_DOWN, GPIOSIM_PULL_UP, GPIOSIM_VALUE_ACTIVE, GPIOSIM_VALUE_INACTIVE, + }; + + const NGPIO: u64 = 8; + + mod invalid_arguments { + use super::*; + + #[test] + fn no_offsets() { + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(None); + config.lconfig_raw(); + + assert_eq!( + config.request_lines().unwrap_err(), + ChipError::OperationFailed("Gpio LineRequest request-lines", IoError::new(EINVAL)) + ); + } + + #[test] + fn duplicate_offsets() { + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[2, 0, 0, 4])); + config.lconfig_raw(); + + assert_eq!( + config.request_lines().unwrap_err(), + ChipError::OperationFailed("Gpio LineRequest request-lines", IoError::new(EBUSY)) + ); + } + + #[test] + fn out_of_bound_offsets() { + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[2, 0, 8, 4])); + config.lconfig_raw(); + + assert_eq!( + config.request_lines().unwrap_err(), + ChipError::OperationFailed("Gpio LineRequest request-lines", IoError::new(EINVAL)) + ); + } + } + + mod verify { + use super::*; + + #[test] + fn custom_consumer() { + const GPIO: u32 = 2; + const CONSUMER: &str = "foobar"; + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig_consumer(Some(&[GPIO]), Some(CONSUMER)); + config.lconfig_raw(); + config.request_lines().unwrap(); + + let info = config.chip().line_info(GPIO).unwrap(); + + assert_eq!(info.is_used(), true); + assert_eq!(info.get_consumer().unwrap(), CONSUMER); + } + + #[test] + fn empty_consumer() { + const GPIO: u32 = 2; + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&[GPIO])); + config.lconfig_raw(); + config.request_lines().unwrap(); + + let info = config.chip().line_info(GPIO).unwrap(); + + assert_eq!(info.is_used(), true); + assert_eq!(info.get_consumer().unwrap(), "?"); + } + + #[test] + fn read_values() { + let offsets = [7, 1, 0, 6, 2]; + let pulls = [ + GPIOSIM_PULL_UP, + GPIOSIM_PULL_UP, + GPIOSIM_PULL_DOWN, + GPIOSIM_PULL_UP, + GPIOSIM_PULL_DOWN, + ]; + let mut config = TestConfig::new(NGPIO).unwrap(); + config.set_pull(&offsets, &pulls); + config.rconfig(Some(&offsets)); + config.lconfig(Some(Direction::Input), None, None, None, None); + config.request_lines().unwrap(); + + let request = config.request(); + + // Buffer is smaller + let mut values: Vec<i32> = vec![0; 4]; + assert_eq!( + request.get_values(&mut values).unwrap_err(), + ChipError::OperationFailed( + "Gpio LineRequest array size mismatch", + IoError::new(EINVAL), + ) + ); + + // Buffer is larger + let mut values: Vec<i32> = vec![0; 6]; + assert_eq!( + request.get_values(&mut values).unwrap_err(), + ChipError::OperationFailed( + "Gpio LineRequest array size mismatch", + IoError::new(EINVAL), + ) + ); + + // Single values read properly + assert_eq!(request.get_value(7).unwrap(), 1); + + // Values read properly + let mut values: Vec<i32> = vec![0; 5]; + request.get_values(&mut values).unwrap(); + for i in 0..values.len() { + assert_eq!( + values[i], + match pulls[i] { + GPIOSIM_PULL_DOWN => 0, + _ => 1, + } + ); + } + + // Subset of values read properly + let mut values: Vec<i32> = vec![0; 3]; + request.get_values_subset(&[2, 0, 6], &mut values).unwrap(); + assert_eq!(values[0], 0); + assert_eq!(values[1], 0); + assert_eq!(values[2], 1); + + // Value read properly after reconfigure + let mut lconfig = LineConfig::new().unwrap(); + lconfig.set_active_low_default(true); + request.reconfigure_lines(&lconfig).unwrap(); + assert_eq!(request.get_value(7).unwrap(), 0); + } + + #[test] + fn set_output_values() { + let offsets = [0, 1, 3, 4]; + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&offsets)); + config.lconfig(Some(Direction::Output), Some(1), Some((4, 0)), None, None); + config.request_lines().unwrap(); + + assert_eq!(config.sim().val(0).unwrap(), GPIOSIM_VALUE_ACTIVE); + assert_eq!(config.sim().val(1).unwrap(), GPIOSIM_VALUE_ACTIVE); + assert_eq!(config.sim().val(3).unwrap(), GPIOSIM_VALUE_ACTIVE); + + // Overriden + assert_eq!(config.sim().val(4).unwrap(), GPIOSIM_VALUE_INACTIVE); + + // Default + assert_eq!(config.sim().val(2).unwrap(), GPIOSIM_VALUE_INACTIVE); + } + + #[test] + fn reconfigure_output_values() { + let offsets = [0, 1, 3, 4]; + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&offsets)); + config.lconfig(Some(Direction::Output), Some(0), None, None, None); + config.request_lines().unwrap(); + let request = config.request(); + + // Set single value + request.set_value(1, 1).unwrap(); + assert_eq!(config.sim().val(0).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(1).unwrap(), GPIOSIM_VALUE_ACTIVE); + assert_eq!(config.sim().val(3).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(4).unwrap(), GPIOSIM_VALUE_INACTIVE); + request.set_value(1, 0).unwrap(); + assert_eq!(config.sim().val(1).unwrap(), GPIOSIM_VALUE_INACTIVE); + + // Set values of subset + request.set_values_subset(&[4, 3], &[1, 1]).unwrap(); + assert_eq!(config.sim().val(0).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(1).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(3).unwrap(), GPIOSIM_VALUE_ACTIVE); + assert_eq!(config.sim().val(4).unwrap(), GPIOSIM_VALUE_ACTIVE); + request.set_values_subset(&[4, 3], &[0, 0]).unwrap(); + assert_eq!(config.sim().val(3).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(4).unwrap(), GPIOSIM_VALUE_INACTIVE); + + // Set all values + request.set_values(&[1, 0, 1, 0]).unwrap(); + assert_eq!(config.sim().val(0).unwrap(), GPIOSIM_VALUE_ACTIVE); + assert_eq!(config.sim().val(1).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(3).unwrap(), GPIOSIM_VALUE_ACTIVE); + assert_eq!(config.sim().val(4).unwrap(), GPIOSIM_VALUE_INACTIVE); + request.set_values(&[0, 0, 0, 0]).unwrap(); + assert_eq!(config.sim().val(0).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(1).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(3).unwrap(), GPIOSIM_VALUE_INACTIVE); + assert_eq!(config.sim().val(4).unwrap(), GPIOSIM_VALUE_INACTIVE); + } + + #[test] + fn set_bias() { + let offsets = [3]; + let mut config = TestConfig::new(NGPIO).unwrap(); + config.rconfig(Some(&offsets)); + config.lconfig(Some(Direction::Input), None, None, None, Some(Bias::PullUp)); + config.request_lines().unwrap(); + config.request(); + + // Set single value + assert_eq!(config.sim().val(3).unwrap(), GPIOSIM_VALUE_ACTIVE); + } + } +} diff --git a/bindings/rust/tests/request_config.rs b/bindings/rust/tests/request_config.rs new file mode 100644 index 000000000000..e914ca8ec887 --- /dev/null +++ b/bindings/rust/tests/request_config.rs @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: Apache-2.0 AND BSD-3-Clause +// +// Copyright 2022 Linaro Ltd. All Rights Reserved. +// Viresh Kumar viresh.kumar@linaro.org + +mod common; + +mod request_config { + use vmm_sys_util::errno::Error as IoError; + + use libgpiod::{Error as ChipError, RequestConfig}; + + mod verify { + use super::*; + + #[test] + fn default() { + let rconfig = RequestConfig::new().unwrap(); + + assert_eq!(rconfig.get_offsets().len(), 0); + assert_eq!(rconfig.get_event_buffer_size(), 0); + assert_eq!( + rconfig.get_consumer().unwrap_err(), + ChipError::OperationFailed("Gpio RequestConfig get-consumer", IoError::new(0)) + ); + } + + #[test] + fn initialized() { + let offsets = [0, 1, 2, 3]; + const CONSUMER: &str = "foobar"; + let rconfig = RequestConfig::new().unwrap(); + rconfig.set_consumer(CONSUMER); + rconfig.set_offsets(&offsets); + rconfig.set_event_buffer_size(64); + + assert_eq!(rconfig.get_offsets(), offsets); + assert_eq!(rconfig.get_event_buffer_size(), 64); + assert_eq!(rconfig.get_consumer().unwrap(), CONSUMER); + } + } +}